SHS / Rocket Airsoft AK Air Nozzle
SHS / Rocket Airsoft Air Nozzle for M16 / M4
SHS / Rocket Airsoft Air Nozzle for Marui / Echo1 M14
Air nozzles wear out and leak air pressure eventually, and if you bought a CYMA / Echo1 M14, it's likely been leaking air since the day you bought it. The SHS M14 air nozzle is machined from aluminum and has a rubber o-ring to maintain a tight air seal helping maintain a consistent FPS in your airsoft gun. Compatible with Marui and CYMA M14'...
SHS / Rocket Airsoft SCAR-L Air Nozzle
SHS / Rocket Airsoft Shims
SHS / Rocket Airsoft Spring Guide (Version 2)
SHS / Rocket Airsoft Spring Guide (Version 3)
SHS / Rocket Airsoft Steel Gears - 16:1 Ratio
SHS 16:1 high speed gears allow you to increase your rate of fire with minimal loss of trigger response. Pair these steel gears with a SHS high torque motor and a lipoly battery and you can have the best of both trigger response and rate of fire. These are one of the best upgrades you can install to improve the reliability of your AEG. 16:1 H...
SHS / Rocket Airsoft Steel Gears - 18:1 Ratio
These are one of the best upgrades you can install to improve the reliability of your AEG. Properly installed, these run great even when powered by a lipoly battery. NOTE: These may be packaged as SHS or Rocket Airsoft but they are always SHS OEM gears.
SHS / Rocket Airsoft Torque Motor (Long Type)
SHS / Rocket Airsoft Torque Motor (Short Type)
SHS torque motors are a great way to improve trigger response or increase efficiency when pulling heavier springs. These motors feature strong magnets and "D" shaped pinion gears for increased torque and reliability and are no slouch when it comes to rate of fire when paired with a high voltage battery. Strong magnets "D" shaped pinion gear E...
SHS 14 Tooth Piston
SHS 14 tooth piston
SHS 14.5 Tooth Piston
SHS 14.5 tooth piston
SHS 6mm Steel Bushing Set
If you are running an older gearbox that is still using nylon bushings then it is time to make the upgrade. SHS steel 6mm bushings are a solid fit in Marui gearboxes and provide a smooth surface for the gear axles without the potential to crack that nylon bushings have.
SHS AEG Cylinder for 350-450mm Inner Barrels
It's important to use the correct volume cylinder with your barrel to maximize your FPS and efficiency. A cylinder that is ported too far forward or too far back can cause your FPS to drop dramatically. Polished Steel construction Ported for AEG's with inner barrels from 350-450 mm in length Fits most AEG's Note: May be packaged as SHS or Ro...
SHS Cut Off Lever (V3)
The SHS cut off lever is a simple upgrade and one that is often overlooked. Most AEG's use a cut off lever made of a mix of poor quality metals instead of steel, and they wear out fast. If you prefer semi-auto, you'll put more wear and tear on the cut off lever, and this is a simple inexpensive upgrade that will improve the reliability of your...
SHS Full Cylinder for AEG with 455mm-510mm inner barrel
It's important to use the correct volume cylinder with your barrel to maximize your FPS and efficiency. A cylinder that is ported too far forward or too far back can cause your FPS to drop dramatically. Polished Steel construction Full Type 0 Cylinder for AEG's with barrels 450mm or longer Fits most AEG's
SHS M110 AEG Spring
SHS M110 spring for most AEG's. 380-400 FPS Irregular pitch for smoother compression, reduced motor strain, and current draw
SHS POM Piston Head
SHS Sector Gear Delayer Chip (Steel)
The SHS steel sector gear delayer chip helps retract the tappet plate a bit longer during each cycle of the gearbox to enhance feeding. If you're running a higher rate of fire setup this will help keep the nozzle retracted just a bit longer to make sure that every round feeds into your hop unit. Steel construction means it will last nearly fore...
SHS V2 / V3 Anti-Reversal Latch
This anti-reversal latch by SHS is all steel and a great upgrade to replace a worn out or broken anti-reversal latch in your version 2 or version 3 gearbox. All steel construction Includes 1 latch and 1 spring Fits Version 2 and Version 3 gearboxes (may fit others as well)
SHS V2 Cylinder Head
shs v2 cylinder head
SHS Version 7 Steel Gears - M14
The SHS version 7 steel gears are the best bang for the buck when it comes to replacing the gears in a Marui style M14 gearbox. These feature the same steel and reliability that the rest of the SHS family of gears provide, but are built to fit version 7 gearboxes.